We will reply to your message within an hour.
More
These nozzles produce a flat, thin spray pattern. They're good for general cleaning, washing, etching, foam control, and applying coatings.
The spray is deflected at a steep angle to produce a low-impact, extra-wide spray.
Spray is deflected at a narrow angle to create the highest impact of all our flat spray nozzles.
Drill a hole anywhere along a pipe and snap on these nozzles. Spray tips can be quickly and easily removed for cleaning and replacement.
These nozzles have replaceable tips that are removable with a quarter-turn.
A check valve prevents the nozzle from dripping when it is turned off. Spray tips can be removed for cleaning and replacement.
A quick-disconnect hose fitting on these nozzles means you can remove and replace them easily to change spray patterns and angles.
A low flow rate makes these nozzles good for distributing fluids, cooling, washing, and rinsing.
Particles in liquid won’t clog these nozzles because of their unique internal and external design.
These nozzles project their spray at a right angle from their threaded connection.
Spray a precise, concentrated, high-velocity stream longer distances than other spray patterns to handle tough cleaning applications.
The large square coverage area makes these nozzles a good choice for chemical processing as well as for cooling applications.
With a unique internal and external design, these nozzles let particles in liquid pass through instead of clogging.
Save time in applications where you often need to replace worn nozzles. These nozzles consist of a base and a nozzle, so you can replace the tip with just a quarter turn.
These nozzles provide a uniform distribution of droplets.
A wide spray angle provides a larger coverage area and produces a finer, more atomized spray than full-cone nozzles.
Fogging nozzles provide smaller, more atomized spray droplets than misting nozzles.
A check valve prevents the nozzle from dripping when it is turned off.
Create small, atomized spray droplets for cooling, moistening, and humidifying applications. These nozzles have a check valve that prevents dripping when they’re turned off
Mixing compressed air and liquid together, these nozzles create an ultra-fine, uniform spray without using high pressures. Also known as air-atomizing nozzles, they make droplets that are less than half the size of other fogging nozzles.
A unique internal and external design lets particles in liquid pass through instead of clogging, leading to higher volumes of mist.
By circulating their spray, these nozzles clean faster with more even coverage and less water than stationary tank-washing nozzles.
Internal gears create controlled motion as fluid moves through these nozzles, maintaining speed and producing large droplets to efficiently clean heavily soiled or large-diameter tanks.
Use these nozzles with detergent that’s diluted in water to create a rotating, multi-directional foam spray for effectively rinsing tanks, drums, and small vessels.
To effectively rinse tanks, drums, and small vessels, these nozzles spray in multiple directions.
Avoid clogs while rinsing tanks, drums, and small vessels. These nozzles have a unique internal and external design, so particles in liquid pass through instead of getting stuck.
Certified by 3-A to meet sanitary design standards, these nozzles have a 360° spray pattern to effectively rinse tanks and vessels in food, beverage, and pharmaceutical environments.
These nozzles produce a flat, thin spray pattern.
Spray a precise, concentrated, high-velocity stream longer distances than flat spray nozzles to handle tough cleaning applications.
No need to juggle multiple nozzles with different spray angles—just turn the cover to adjust the spray angle from 0° to 80°.
The superior cleaning ability of a solid stream has been combined with rotating spray action for excellent coverage.
Push the nozzle out for lower pressures and pull it back for higher pressures. Turn the cover to adjust the spray angle from 0° to 25° or 75°.
No need to switch between nozzles—push these nozzles in and pull them out to change their pressure level, and twist their cover to adjust the spray angle between 0° and 40°. Their quick-disconnect hose connection makes attaching and removing them easy.
Instead of swapping between nozzles, turn the cover on these nozzles to change their spray angle. They have quick-disconnect couplings for easy detachment.
Combining rotation with a solid stream, these nozzles spray in a 25° hollow cone shape to cover a wide area. They’re easy to remove thanks to their quick-disconnect hose connection.
Specifically designed for steam, these nozzles direct steam better than standard spray nozzles.
FM approved for use in fire-protection applications, these nozzles produce a heavy, coarse spray to quickly put out fires.
Attaching a spray nozzle to these swivel fittings allows the nozzle to swivel 360° and tilt on a 45° range.
Build a spray system by adding your own nozzles to these nozzle-ready spray manifolds.
Drill a hole in your pipe and connect one of these fittings to create a connection point for a spray nozzle or swivel fitting.
For light duty spray-down applications, attach these wash guns to any standard garden hose.
These durable wash guns are typically used for frequent washdowns and cleanup.
These wash guns have a high maximum pressure, so use them with pressure washers and high-pressure spray systems.
Use these guns to clean as well as apply chemicals and solvents.
Connect these guns to your garden hose and automatically dispense solution from the attached bottle instead of dragging around a siphon hose.
The powerful combination of air and water creates a high-velocity, atomized spray without needing high pressure. These guns also can be used to siphon.
Clean hard-to-access areas by extending the reach of your quick-disconnect wash gun.
With a high maximum pressure and quick-disconnect nozzle connection, these wash guns work with pressure washers and high-pressure spray systems and it’s easy to swap out their nozzles.
Clean and sanitize surfaces with the power of steam—with or without detergents and other chemicals.
Combine the power of steam and detergent—siphon detergent from a drum and use the control panel to regulate the steam/detergent mixture and change the temperature and flow rate.
Connect these cleaners to existing steam lines to remove dirt, grease, and heavy oils from most surfaces.
Use as either a vacuum or a blower—change the airflow direction to switch functions. Use to clean up dirt, dust, metal chips, and glass.
The flat nozzle tip distributes air over a wider area than focused-airflow nozzles.
These nozzles are made of FDA-listed materials.
Adjust airflow to control consumption and noise.
Air blows out of these nozzles at a right angle in a wide pattern, distributing air over a wider area than focused-airflow nozzles.
At less than 2" long and with a wide airflow pattern, these nozzles are ideal for tight spaces where you need to distribute air over a wider area than a focused-airflow nozzle.
Air blows out of these flat nozzles in a wide pattern at a 90° angle from the inlet, distributing air over a wider area than focused-airflow nozzles. They’re FDA compliant 21 CFR 110.40 for use in the food industry.
These premium nozzles are engineered for the most efficient airflow consumption.
Also known as air-shield and safety-shield nozzles, a center airstream blows away debris while an outer air curtain deflects flying chips and dust.
Made from rubber, these nozzles won’t scratch or damage sensitive workpieces.
Control consumption and noise by adjusting the airflow.
Attach to your blowgun to direct airflow.
Extend these telescoping nozzles to increase your reach.
The extra length allows access into hard-to-reach areas.
These needle-style nozzles force air to a precise pinpoint.
Focus air with pinpoint precision.
Blow air backward to clean out the inside of pipes, tubes, and channels without pushing debris into your system.
As compressed air flows through these nozzles, they rotate to efficiently and evenly blow off large areas.
Nozzles are attached to a flexible hose that bends and holds its shape until you reposition it.
The magnetic base mounts to your work surface and has a control valve for adjusting airflow.
Choose a base, hose, and nozzle for a custom setup.
Convert your blowgun to a spray gun. These nozzles spray air and liquids at the same time.
Shaped to fit into extremely tight spaces, these nozzles can be used to remove parts from molds. Tap the wedge into position, attach the nozzle to a blowgun, and activate the airflow to release the part.
Attach one of these swivels to an air nozzle to direct air 30° left, right, up, and down.
Often used for simultaneously spot cooling and blowing parts, these nozzles cool compressed air without electricity or refrigerants.
Blow debris and sweep it away with the built-in brush.
Turn your blowgun into a scraper to remove and blow away debris at the same time.
These blowguns have a metal body.
The lightweight plastic construction makes these blowguns more comfortable to hold than metal.
The rubber tip won't damage parts.
Also known as air-shield and safety-shield blowguns, a center airstream blows away debris while an outer air curtain deflects flying chips and dust.
Compact enough to carry with you, these guns have a built-in quick-disconnect hose coupling for easy connection to an air line.
Designed to reduce noise, these blowguns are quieter than similar standard guns.
Two inlets allow connection to air lines above or below. Use the top inlet when the blowgun is suspended from an overhead hose and the bottom inlet for bench and floor hoses.
Operate a blowgun without disconnecting your air tool—these guns fit between the tool and air hose. Good for blowing away debris after using an air-powered sander or grinder.
Connect the included hose to your air supply and these blowguns are ready to use.
The extra length lets you access hard-to-reach areas.
The included hose is ready to connect to your air supply.
The lightweight plastic body is more comfortable to hold than metal.
These guns include a rubber tip that won't damage your workpiece.
Also known as air-shield and safety-shield blowguns, an outer air curtain deflects flying chips and dust while the center airstream blows away debris.
Increase your reach with the telescoping nozzle.
Maximize comfort and minimize strain with these lightweight guns.
These blowguns provide more than two times the airflow of standard guns.
Air flows out of the side of the nozzle to clean air filters, radiators, and inside recesses.
The flat nozzle distributes air over a wide area.
Clear dust and debris, test air ducts for leaks, and dry large surfaces without needing a compressed air line.
The most powerful blowguns we sell, these use compressed air to clean and blow debris.
Blow air backward from the nozzle to clean out the inside of pipes, tubes, and channels without pushing debris into your system.
Also known as siphon guns, these spray air and liquids at the same time. Push the lever and the airflow creates suction that draws water, cleaning solution, or other liquids through the hose.
A nonconductive plastic nozzle and tip protect against accidental contact with live electrical circuits. These blowguns are tested to 1,000 volts to meet IEC 60900.
Clean surfaces without transferring dust or moisture from the air hose. These blowguns have a replaceable filter that traps particles such as rust and smoke and absorbs moisture.
Safely blow dust and debris off your clothes. These blowers are a safer alternative to compressed air and help you meet OSHA regulations.
Bend the stand's flexible arm to position your gun and keep it in place. Use the included foot pedal to activate airflow and static elimination.
These guns provide more than three times the airflow of standard static-eliminating blowguns.
Blow off dust and contamination, eliminate static charges, and guard against ESD (electrostatic discharge).
Secure an air knife to the bracket and position where needed. Two swiveling joints allow 360° movement.
Create a sheet of high-velocity air.
Use one bracket for 3" to 18" wide air knives; two brackets for 24" to 42" wide air knives, and three brackets for 48" wide air knives.
Producing the same airflow as standard air knives, these are quieter and use 18% less compressed air.
Also known as air wipes, these use a 360° airstream to blow off, dry, clean, and cool tubes, cables, extruded shapes, and hoses.
Dry and cool parts, wipe conveyor belts, control coating depth, and blow liquid, chips, and dust off of equipment in sanitary environments.
Attach to a blower for high-speed airflow at low pressure.
An ionizing bar temporarily neutralizes static to protect against ESD (electrostatic discharge).
These produce the same airflow as standard static-eliminating air knives but are quieter and use 15% less compressed air.
Launch foam cylinders through hose and tubing to power away dirt and deposits. Unlike cleaners with brushes, these work on flexible, curved, and coiled tubing as well as those with fittings, valves, and 90° bends.
Create a wide airflow that’s good for drying and stripping paint.
Sets include a focused nozzle for concentrated airflow, a flat-tip nozzle for heating wide surfaces, and a deflecting nozzle that protects adjacent surfaces from heating.
A deflector protects adjacent areas from heating. The flat shape creates a wide airflow.
Insert plastic welding rod through a second opening in the nozzle. It directs air to heat the rod and weld plastic.
Concentrate a heat gun's airflow.
Shaped to hold round objects, use these nozzles for installing heat-shrink tubing and bending plastic pipe.
Prevent accidental contact with hot nozzles.
Build a custom 1/4" system to deliver coolant, cutting oil, water, or air in any direction.
Kits contain lengths of hose, nozzles, valves, and caps.
Build a custom 1/2" system to deliver coolant, cutting oil, water, or air in any direction.
Build a custom 3/4" system to deliver coolant, cutting oil, water, or air in any direction.
Kit contains lengths of hose, nozzles, connectors, and assembly pliers.
Use with Loc-Line hose to assemble and disassemble components.
Use with Snap-Loc hose to assemble and disassemble components.
This hose is made of steel.
The most versatile of our machine-mount coolant nozzles, these adjust from a fine mist to a direct stream and can deliver coolant in any direction. Max. pressure is 100 psi.
These nozzles handle coolant pressure up to 150 psi.
For use in the highest pressure coolant lines, these nozzles are rated for at least 1,000 psi.
Use as a lever to adjust the angle of coolant streams.
For high-pressure coolant lines, these nozzles withstand pressure up to 500 psi.
Press these nozzles into unthreaded holes.
Draw coolant from your existing tank.
These dispensers have a reservoir and controls for coolant flow.
Press the lever to stop coolant mist and start a high-velocity air stream to remove dust and shavings.
These dispensers have a reservoir for recirculating coolant.
Replace messy mist coolant dispensers—these convert compressed air into a stream of cold air. They can be used in applications where liquid coolant can't.
Deliver a small, controlled amount of coolant to a workpiece.
Snap these adapters into the ball-socket connections on CNC machines to connect threaded coolant hose and nozzles to coolant supply ports.
Connect these modular pumps to a reservoir and a solenoid valve to automate the flow of oil.
Twist the barrel to adjust water flow.
There’s no shut-off valve on these nozzles, so water instantly flows.
Use the lever to turn water flow on and off.
Adjust the flow while dispensing liquid chemicals.
These nozzles let you adjust the flow while dispensing gasoline. They are also known as service-station-style nozzles.
Control the flow while dispensing diesel fuel with these nozzles.
Dispense and control the flow of coolant with these nozzles.
Nozzles allow you to control the flow while dispensing hydraulic fluid.
Attach these chucks to your air hose so you can connect the hose to Schrader valves.
Attach these nozzles to your high-pressure water line to flush grit and grime out of blocked pipes.
Keep electronics inside enclosures from overheating by converting compressed air into a stream of cold air.
Set the thermostat and these vortex tubes switch on only when needed.
Often used in low-noise environments such as labs and clean rooms, these are quieter than standard enclosure-cooling vortex tubes.
In addition to being quieter than standard enclosure-cooling vortex tubes, these stand up to washdowns and weather. They convert compressed air into a stream of cold air to keep electronics within enclosures from overheating while also keeping dust and other contaminants out.
These NEMA-rated vortex tube are designed to keep water out during washdowns.
UL classified for hazardous locations, these vortex tubes convert compressed air into a stream of cold air to keep electronics within enclosures from overheating while also keeping dust and other contaminants out.
Quietly cool electronics inside enclosures while keeping out rain, snow, splashing water, and dirt.
Cool electronics inside enclosures while keeping out rain, snow, splashing water, and dirt.
Cool electronics inside enclosures to your desired temperature while keeping out rain, snow, splashing water, and dirt.
Quietly cool electronics inside enclosures to your desired temperature while keeping out rain, snow, splashing water, and dirt.
Vortex tubes convert compressed air into a stream of cold air.
Kits include one vortex tube for converting compressed air into a stream of cold air as well as airflow adjusters, a cold-air muffler, a tube fitting, and tubing.
Mate these gauges to a compressed air line to measure pressure while inflating tires.