We will reply to your message within an hour.
Once aftercoolers and separators have removed the bulk of the water, use these dryers to remove any remaining moisture in your air line.
For use with Norgren modular compressed air systems, once aftercoolers and separators have removed the bulk of the water, use one of these desiccant-filled dryers to remove any remaining moisture in your air line.
Get dry compressed air in high-pressure systems—these dryers have a maximum pressure rating of 300 psi. Once aftercoolers and separators have removed the bulk of the water, they remove any remaining moisture in your air line.
Use these dryer/filters to protect air-powered tools from water, oil, oil vapor, and particles, then throw them away when you're done.
These dryer/filters have a clay desiccant that removes moisture, oil, and particles, so there’s no need to install a separate filter and dryer. Once aftercoolers and separators have removed the bulk of the water, they remove any remaining moisture in your air line.
With a clear polycarbonate bowl that’s visible from all angles and silica gel desiccant that changes from blue to pink, it’s easy to see when it’s time to change the cartridge on these dryer/filters and dryer/filter/regulators.
Each of these filter/dryers has two desiccant towers—one that absorbs moisture, particles, and oil in the air while the other reactivates saturated desiccant so you have an uninterrupted supply of clean, dry compressed air.
Install these dryers just before air-powered tools as final protection from water and particles and throw them away when you’re done.
These all-in-one dryer/filters eliminate the need for individual dryers, separators, and filters. They cool air through refrigeration to condense water vapor for removal.
Cool air through refrigeration to condense water vapor.
A float-operated drain valve on these separators automatically opens when the bowl begins to fill. The first step in water removal, use one of these separators to remove the large amount of water as compressed air cools.
These separators have higher flow rates compared to our other compressed air separators. Prevent equipment damage and wear caused by moisture in your compressed air supply. The first step in water removal, use one of these separators to remove the large amount of water created as compressed air cools.
In addition to removing large amounts of water, these separators also remove particles and oil droplets. Place them after your compressor and aftercooler, or at the point of use in applications that don't require an aftercooler.
When water is condensed out of a compressed air system, it contains oil from the compressor that makes disposal difficult. These separators use two-stage filtration to reduce oil content to below 20 parts per million.
Also known as regenerative blowers, use these to produce high-flow compressed air with low pressure or vacuum to operate pump drives, lift tables, and conveying systems.
Safely produce high-flow compressed air with low pressure or vacuum in environments with flammable gases and combustible dust, such as propane and carbon-based dust. These blowers have an explosion-proof motor and are UL listed for use in hazardous locations.
Create a high-flow air stream from your compressed air supply. Flow boosters draw in ambient air, which amplifies compressed air flow.
Use a low-flow air pilot signal with an air supply to produce flow up to 50 cfm to actuate valves and other air-powered system components.
Also known as coalescing filters, these filter elements fit in Parker modular compressed air filters to remove oil and particles as small as 0.01 microns.
Also known as coalescing filters, these filter elements fit in SMC modular compressed air filters to remove oil and particles as small as 0.01 microns.
Also known as coalescing filters, these filter elements fit in Wilkerson modular compressed air filters to remove oil and fine particles.
Also known as coalescing filters, these filter elements fit in Festo modular compressed air filters to remove oil and particles as small as 0.01 microns.
Also known as coalescing filters, these filter elements fit in ASCO Numatics modular compressed air filters to remove oil and particles as small as 0.01 microns.
Also known as coalescing filters, these filter elements fit in Norgren modular compressed air filters to remove oil and particles as small as 0.01 microns.
Also known as coalescing filters, these filter elements fit in ARO modular compressed air filters to remove oil and particles as small as 0.3 microns.
Replace the filter element in your Wilkerson modular compressed air filter to trap solid particles and water droplets as small as 5 microns.
Replace the filter element in your SMC modular compressed air filter to trap solid particles and water droplets as small as 5 microns.
Replace the filter element in your Norgren modular compressed air filter to trap solid particles and water droplets as small as 5 microns.
Replace the filter element in your Parker modular compressed air filter to trap solid particles and water droplets.
Replace the filter element in your Festo modular compressed air filter to trap solid particles and water droplets as small as 5 microns.
Replace the filter element in your ARO modular compressed air filter to trap solid particles and water droplets.
Replace the filter element in your ASCO Numatics modular compressed air filter to trap solid particles and water droplets as small as 5 microns.
These filter elements fit in ASCO Numatics modular two-stage compressed air filters to remove water droplets, oil, and particles as small as 0.01 microns.
Get clean, dry air wherever you need it. The separator, filter, and dryer mounted on these tanks clean and dry compressed air as you fill it. Once full, move the tank to your workspace on its pneumatic wheels.
These blowguns have a metal body.
The lightweight plastic construction makes these blowguns more comfortable to hold than metal.
The rubber tip won't damage parts.
Also known as air-shield and safety-shield blowguns, a center airstream blows away debris while an outer air curtain deflects flying chips and dust.
Compact enough to carry with you, these guns have a built-in quick-disconnect hose coupling for easy connection to an air line.
Designed to reduce noise, these blowguns are quieter than similar standard guns.
Operate a blowgun without disconnecting your air tool—these guns fit between the tool and air hose. Good for blowing away debris after using an air-powered sander or grinder.
Two inlets allow connection to air lines above or below. Use the top inlet when the blowgun is suspended from an overhead hose and the bottom inlet for bench and floor hoses.
Connect the included hose to your air supply and these blowguns are ready to use.
These guns include a rubber tip that won't damage your workpiece.
The extra length lets you access hard-to-reach areas.
The included hose is ready to connect to your air supply.
The lightweight plastic body is more comfortable to hold than metal.
Also known as air-shield and safety-shield blowguns, an outer air curtain deflects flying chips and dust while the center airstream blows away debris.
Increase your reach with the telescoping nozzle.
Maximize comfort and minimize strain with these lightweight guns.
These blowguns provide more than two times the airflow of standard guns.
Air flows out of the side of the nozzle to clean air filters, radiators, and inside recesses.
The flat nozzle distributes air over a wide area.
Clear dust and debris, test air ducts for leaks, and dry large surfaces without needing a compressed air line.
The most powerful blowguns we sell, these use compressed air to clean and blow debris.
Blow air backward from the nozzle to clean out the inside of pipes, tubes, and channels without pushing debris into your system.
Blow off dust and contamination, eliminate static charges, and guard against ESD (electrostatic discharge).
Bend the stand's flexible arm to position your gun and keep it in place. Use the included foot pedal to activate airflow and static elimination.
These guns provide more than three times the airflow of standard static-eliminating blowguns.
Clean surfaces without transferring dust or moisture from the air hose. These blowguns have a replaceable filter that traps particles such as rust and smoke and absorbs moisture.
A nonconductive plastic nozzle and tip protect against accidental contact with live electrical circuits. These blowguns are tested to 1,000 volts to meet IEC 60900.
Safely blow dust and debris off your clothes. These blowers are a safer alternative to compressed air and help you meet OSHA regulations.
These premium nozzles are engineered for the most efficient airflow consumption.
Made from rubber, these nozzles won’t scratch or damage sensitive workpieces.
Control consumption and noise by adjusting the airflow.
Also known as air-shield and safety-shield nozzles, a center airstream blows away debris while an outer air curtain deflects flying chips and dust.
Attach to your blowgun to direct airflow.
Extend these telescoping nozzles to increase your reach.
The extra length allows access into hard-to-reach areas.
Blow air backward to clean out the inside of pipes, tubes, and channels without pushing debris into your system.
Adjust airflow to control consumption and noise.
The flat nozzle tip distributes air over a wider area than focused-airflow nozzles.
These nozzles are made of FDA-listed materials.
At less than 2" long and with a wide airflow pattern, these nozzles are ideal for tight spaces where you need to distribute air over a wider area than a focused-airflow nozzle.
Air blows out of these nozzles at a right angle in a wide pattern, distributing air over a wider area than focused-airflow nozzles.
Air blows out of these flat nozzles in a wide pattern at a 90° angle from the inlet, distributing air over a wider area than focused-airflow nozzles. They’re FDA compliant 21 CFR 110.40 for use in the food industry.
These needle-style nozzles force air to a precise pinpoint.
Focus air with pinpoint precision.
As compressed air flows through these nozzles, they rotate to efficiently and evenly blow off large areas.
Nozzles are attached to a flexible hose that bends and holds its shape until you reposition it.
The magnetic base mounts to your work surface and has a control valve for adjusting airflow.
Choose a base, hose, and nozzle for a custom setup.
Shaped to fit into extremely tight spaces, these nozzles can be used to remove parts from molds. Tap the wedge into position, attach the nozzle to a blowgun, and activate the airflow to release the part.
Often used for simultaneously spot cooling and blowing parts, these nozzles cool compressed air without electricity or refrigerants.
Convert your blowgun to a spray gun. These nozzles spray air and liquids at the same time.
Blow debris and sweep it away with the built-in brush.
Turn your blowgun into a scraper to remove and blow away debris at the same time.
Create a sheet of high-velocity air.
Producing the same airflow as standard air knives, these are quieter and use 18% less compressed air.
Also known as air wipes, these use a 360° airstream to blow off, dry, clean, and cool tubes, cables, extruded shapes, and hoses.
Dry and cool parts, wipe conveyor belts, control coating depth, and blow liquid, chips, and dust off of equipment in sanitary environments.
Attach to a blower for high-speed airflow at low pressure.
An ionizing bar temporarily neutralizes static to protect against ESD (electrostatic discharge).
These produce the same airflow as standard static-eliminating air knives but are quieter and use 15% less compressed air.
Use these blowers for production drying, heat shrinking, and other applications requiring heat over 1000°F.
Combine high-volume airflow with low-heat output for warming and drying.
Blast your heating, drying, and shrinking projects with hot air to get the job done quickly. Choose from blowers with temperature settings from 300° to 750° F.
Sets include a focused nozzle for concentrated airflow, a flat nozzle for heating wide surfaces, and a curved nozzle for installing heat-shrink tubing.
Replace filters or add parts baskets and drum dollies to your parts cleaning vacuum/blowers. All of these filters and accessories can be used with compatible MiJET parts cleaners.
Clean parts with compressed air without propelling fluids and debris all over your shop. These vacuum/blowers quickly blow coolant, oil, and chips off your parts while a vacuum sucks them into a removable drum for recycling or disposing of them.
The body rotates to direct air where it’s needed.
Dry large flat surfaces such as floors with a concentrated stream of air.
To quickly dry flat surfaces, these fans direct air downward.
These blowers have an explosion-proof motor that is UL listed for hazardous locations. They also have an aluminum housing for spark resistance.
Powerful and durable, these blowers are able to blow air through larger systems that have more airflow resistance than standard hazardous location spark-resistant blowers can handle.
These blowers have an aluminum housing for spark resistance.
Powerful and durable, these blowers are able to blow air through larger systems that have more airflow resistance than standard spark-resistant blowers can handle.
Install these blowers into ductwork where high static pressures are present.
Operate these blowers with a DC power source, such as your vehicle battery.
Powerful and durable, these blowers are able to blow air through larger systems that have more airflow resistance than standard blowers can handle.
These blowers have a motor that is UL listed for Class I, Divisions 1 and 2, Group D; and Class II, Divisions 1 and 2, Groups F and G hazardous locations.
Quickly ventilate smoke, gas, and other fumes by forcing fresh air into your space instead of exhausting air out.
For resistance to chemicals as well as corrosion, these blowers have a plastic housing.
A 304 stainless steel housing offers good corrosion resistance.
Use your compressed air source to power these blowers.
These blowers operate on 120V AC.
In addition to blowing twice as much air as other portable blowers, these have a motor that is UL listed for Class I, Divisions 1 and 2, Group D; and Class II, Divisions 1 and 2, Groups E, F, and G hazardous locations.
Blow twice as much air as other portable blowers.
A plastic housing offers good corrosion resistance.
Create a more concentrated stream of air than equipment-cooling fans to blow away the heat generated by electronic equipment, induction heaters, and high-wattage bulbs.
For use in tight spaces where other equipment-cooling blowers won't fit, air enters through the center of the unit and then expels along the edges.
Also known as crossflow blowers, these create a wider stream of air than other equipment-cooling blowers.
Create a more concentrated stream of air than enclosure-cooling fans to cool equipment faster.
Place these dehumidifiers in small spaces to protect moisture-sensitive materials such as photo lenses or 3D printing filaments. While they don’t need a battery or power cord during use, you do plug them in to dry them out—unlike other desiccants, they don’t require an oven.
Warm the air in small rooms to reduce humidity.
A reservoir collects moisture.
Use for more demanding jobs such as water damage restoration work.
Reduce paper waste in your lavatory by installing one of these motion-activated hand dryers.
These two-speed hair dryers store in their wall-mounted cradle when not in use.